Connect the power to your AppCam. The AppCam will install the firmware. Note: It may be necessary to perform the initial setup again for the AppCam and your mobile phone application. This installer creates the following driver on your system: v2. Install Instructions. You will need this to unlock the full version of the program.
There is no charge for the full version of this software. Release Notes. To enter registration key: open program, click on "write to scanner", click on "setup" at top and then "registration". The Turbo Search feature, new for Uniden scanners, can search v. Unique Data Skip Allows the scanner to skip over unwanted data transmissions and reduces birdies. Memory Backup The stored channels are retained in memory for at least 3 days, and typically 14 days, when the Battery Pack is removed from the scanner.
Memory Bank Numbers — Each Memory Bank consists of 10 channels that you can select or deselect during scanning operation, using the numeric keypad. When you select a Bank, its number appears on the display. In this mode, when the scanner monitors an active frequency, searching or scanning will not resume until transmission stops for 2 seconds. Page 9 Use to enter the decimal point when programming a frequency into a channel. If you make an entry error, press erase the entry, and start over.
Press to store a displayed frequency into any displayed channel. Use or down direction within a Band, or to go up or down in frequency when Search is stopped.. After about 10 minutes, the scanner will shut itself off to prevent the battery from becoming completely discharged. Before charging, you must first install the Battery Pack according to the steps below. Place the Belt Clip on the mounting area on the back of the scanner, making sure the holes in the clip line up with the threads in the back of the scanner.
Insert the 2 screws into the corresponding holes and tighten. If the Delay Mode is on, the scanner remains on the same channel for 2 more seconds, waiting for a responding transmission. If there is no responding transmission within 2 seconds, the scanning cycle resumes.
Page 13 If the Delay Mode is on, the scanner remains on the same channel for 2 more seconds, waiting for a responding transmission. If there is no responding transmission within 2 seconds, the search cycle resumes.
Page Programming Channels Directory. Program Page Programming With Search Press display will blink twice to confirm the programming. If you want to store the frequency in the selected channel 18 as well, press blink twice to confirm the programming. Page 16 Press repeatedly to cycle through each of the 12 preprogrammed Search Bands until you see the Band you want. Wait for at least 2 seconds for Search to begin. Or press When Search stops on a desired frequency, press to stay on that frequency.
The next available empty channel will be blinking on the display. Page Scanning Note: When you turn the scanner on it will be in the same Mode it was in when you turned it off.
Bank Scanning Look at the upper left corner of the display. If a transmission is received, the scanner will stop at that channel. Page Delay You may have programmed certain channels that you do not want to hear every time you scan. These are channels that are busy a major portion of the time, and the scanner stops at the channel s often enough to interrupt the scan cycle. You can Lock Out those channels so they are not scanned. Page Looking For "Locked Out" Channels For added convenience, there are 10 corresponding channel identifiers on a Memo Pad on the front of the scanner.
Find the frequencies you want using the enclosed SportCat Frequency Guide. There are listings for all types of events, such as: Auto Racing, Boat Racing, various show tours, Golf Tournaments, and more. Page 21 a. Page Priority Scan To access a specific channel: Press Enter the channel number using the numeric keys.
Press again. Initially these are the first channel in each Bank. Channel 1, Channel 11, Channel 21, and so on. In priority scan mode, the scanner checks the Priority Channel s every 2 seconds during the Scan cycle. Page Locking Out Channels Locking Out Channels You may have programmed certain channels that you do not want to hear every time you scan. These might be channels that are busy a major portion of the time, causing the scanner to stop at the channel s often enough to interrupt the scan cycle.
You can search any of these Bands to find desired frequencies if you do not have a Frequency Directory handy, or if new stations have been added since the Directory was published. Page Search Skip Frequency Enter the higher limit of your search range. Press Press appears on the display. In Manual mode, enter the frequency by using the number keypad and turnVFO control. Turn the scanner over so you are looking at the back.
If the Belt clip is attached, remove it by taking out the two screws. Press in on the ribbed area and slide the Battery Cover down and off. Do not use excessive amounts of water. Repairs Do not attempt any repair. The scanner contains no serviceable parts. Contact the Uniden Customer Service Center or take it to a qualified repair technician. Page Birdies Birdies All scanners are subject to receiving undesired signals or birdies. Birdies are internally generated signals inherent in the electronics of the scanner.
Use the Search Skip feature to skip the unwanted frequencies. Page Troubleshooting If you still cannot get satisfactory results and want additional information, or to return the unit for service, please call or write the Uniden Parts and Service Division. The address and phone number are listed in the Warranty at the end of this manual. Page 33 Size: Weight: Power Requirements: 4. Features, specifications, and availability of optional accessories are all subject to change without notice.
UBZZZZ 4,, 4,, 4,, 4,, 4,, 5,, 5,, 5,, 5,, 5,, 5,, 5,, All rights reserved. Printed in the Philippines
0コメント