Dry vent installation

Mark a circle where the opening will be from the inside of your home using a section of a vent pipe. Place the vent cap over the hole, on the high point of the siding, and double-check its position. Do not caulk along the bottom as you want any moisture that gets behind the hood to be able to escape. The next step is cutting the rigid dryer duct pipe that will connect your dryer with the exit point. Just make sure you wear gloves when handling and assembling the cut pieces of duct pipe.

The freshly cut edges are extremely sharp! Secure the vent ducts using foil tape around the seams to seal the connections. Avoid using screws as these can collect lint inside. Once everything is attached and secured, slide the dryer back into place and use a level to ensure it rests flat on the floor. Finally, turn on the dryer to check the flow of the dryer vent installation.

You should also check outside to make sure that the flap on the vent is operating properly. Are you ready to tackle dryer vent installation?

Start shopping for a high-quality dryer vent at Copperlab. Repair Or Replace. Sign In. Explore Ranges Shop All Ranges. Explore Dishwashers Shop All Dishwashers. Explore Microwaves Shop All Microwaves. Explore Cooktops Shop Cooktops.

Explore Freezers Shop Freezers. Create Your Account To purchase a water filter subscription, you must create an account or sign in to your existing account.

Link Example. Sign in with Facebook. Yes, I'd like to receive occasional special offers, promotions, or other e-mail marketing communications from Maytag and its affiliated brands.

For more information about our privacy practices and a list of affiliated brands, please read out Privacy Notice. I agree to the Terms of Use and Privacy Notice.

Create an Account. Yes Skip. Click to view our Accessibility Statement. How to Install a Dryer Vent in 6 Steps. Tools Tape measure Screwdriver Vacuum Protective work gloves. To clean venting, follow these steps: Disconnect any existing ducting from the dryer exhaust outlet and the wall. Use the hose of your vacuum to suck up any remaining lint. Learn how to prepare for appliance delivery with this Maytag guide.

Item added to the compare list, you can find it at the end of this page. Comparing 0 Items. Model: Color: Quantity: Subscribe to Receive :. Proceed to Cart Continue Shopping. Learn More. X Recommendations. Measure the offset distance between the center of the dryer discharge vent and the center of the wall vent to which you need to connect. Purchase the appropriate sized offset dryer vent kit.

You should buy the smallest sized kit that will work. Remove the offset duct from the box, then adjust the two vent connection holes to the correct spacing by sliding the two ends apart or closer together. Once set to the correct location, affix the ends in place by using HVAC aluminum foil tape to seal the open joints and lock the sliding duct into position. Do not use standard duct tape, which quickly dries out and fails to seal the joint.

A tight seal is critical because, with a gas dryer, the vent exhausts not only lint and air but also carries deadly carbon monoxide gas to the outdoors. Connect the appropriate end of the offset duct typically the smaller diameter end to the wall connection duct. There is not much space to work, and you do not want the offset duct falling off once the dryer is being positioned in place, so attach it with aluminum foil duct tape by placing the offset duct at the approximate angle needed for the final connection to the dryer.

Move the dryer into position, sliding the offset dryer vent connection over the dryer's discharge vent. Make sure there is a snug fit, then move the band clamp over the duct connectors and tighten, using a screwdriver or socket driver.

Plug the dryer in and turn on the appliance. Check for proper operation and make sure the exhaust ducts remain connected. Keep your home safer by following dryer operation safety procedures , including cleaning the lint trap and dryer vent of lint buildup on a regular basis.

Once every couple of years, have a qualified service person clean the interior of the dryer chassis to minimize the amount of lint accumulation. Keep the area around the dryer clean and free of clutter. In most cases, the opening must be four and a quarter inches wide for confirmation, consult the instructions provided by the manufacturer. I suggest drilling a pilot hole first, then going outside to double-check its position.

Install the dryer vent cap against the side of your house, being sure that its attached pipe fits through the wall opening you have made. Now go inside and connect the dryer duct to the vent cap pipe a degree elbow may be needed , securing the connection with a hose clamp. Having moved the dryer into the desired spot in your laundry room, measure the distance from the back of the machine to the vent opening, accounting for all the necessary turns in the ductwork.

With a pair of tin snips , proceed to cut the tubing to the length of the measured distance. If you are joining more than one length of tubing, reinforce all joints with foil tape.

Switch on the dryer, then go outside to inspect the vent cap: It should be emitting warm air. The most likely explanation is that one of the connections has come undone.